Practical guide · Safety management
OSHA penalties and the top 10 most cited standards (FY2026)
Short answer
In 2026 the maximum OSHA penalty is $16,550 per serious or other-than-serious violation and $165,514 per willful or repeated violation. The most cited standard in OSHA's preliminary fiscal year 2026 list is fall protection in construction, 29 CFR 1926.501.
OSHA did not raise its penalties for 2026: a memo of 21 May 2026 keeps the 2025 amounts, because the October 2025 inflation data was never produced. A serious violation can cost up to $16,550, a willful or repeated one up to $165,514, and failure to abate up to $16,550 for each day past the abatement date. The 10 standards OSHA cited most in fiscal year 2026 are fall protection, hazard communication, lockout/tagout, scaffolding, ladders, respiratory protection, powered industrial trucks, fall protection training, eye and face protection, and machine guarding. Each one can be checked on a schedule before an inspector checks it.
Last reviewed:
OSHA maximum penalties for 2026
These are the federal OSHA civil penalty amounts in force for 2026, by type of violation. The maximums are set by statute and adjusted for inflation. The minimums come from OSHA's penalty policy: the lowest gravity level with the largest reductions OSHA allows, except for willful violations, whose minimum is set by statute.
| Type of violation | Minimum | Maximum |
|---|---|---|
| Serious | $1,085 per violation | $16,550 per violation |
| Other-than-serious | $0 per violation | $16,550 per violation |
| Willful | $11,823 per violation | $165,514 per violation |
| Repeated | $4,256 per violation | $165,514 per violation |
| Posting requirements | $0 per violation | $16,550 per violation |
| Failure to abate | Not applicable | $16,550 per day unabated beyond the abatement date, generally limited to 30 days |
Source: OSHA memo of 21 May 2026, 2026 OSHA Civil Penalties Update: No Inflation Adjustment and Updated Minimum Penalties, Table 1 (osha.gov/memos/2026-05-21/2026-annual-adjustments-osha-civil-penalties). The maximums match OSHA's Penalties page (osha.gov/penalties) and 29 CFR 1903.15(d), read on 21 November 2026.
Why the 2026 penalties are the same as 2025
OSHA normally adjusts its maximum penalties for inflation every year. For 2026 it did not. The 21 May 2026 memo says there are no inflation-based increases for 2026 and the 2025 amounts stay in effect, because the Bureau of Labor Statistics could not produce the October 2025 consumer price data during the government shutdown. 29 CFR 1903.15(d) states the same maximums for penalties proposed after 15 January 2025, and the Department of Labor published its 2026 notice in the Federal Register on 27 May 2026.
Repeated other-than-serious violations
An other-than-serious violation can carry no penalty the first time. If it is repeated, the memo sets a gravity-based penalty of $472 for the first repeat, $1,182 for the second and $2,364 for the third.
States that run their own OSHA-approved plan must adopt maximum penalties at least as effective as federal OSHA's, so check your state plan if you are not under federal OSHA.
The top 10 most cited OSHA standards, fiscal year 2026
Each year OSHA publishes the standards it cited most often after inspections of worksites by federal OSHA. The list below is the preliminary list for fiscal year 2026, which runs from 1 October 2025 to 31 August 2026, as published on OSHA's Top 10 page (updated 5 October 2026). OSHA does not give the number of citations on that page. Five of the ten are construction standards (29 CFR 1926) and five are general industry standards (29 CFR 1910).
| Rank | Standard | 29 CFR | Template to check it |
|---|---|---|---|
| 1 | Fall protection, general requirements (construction) | 1926.501 | Fall Protection Program Audit and Fall Arrest Equipment Inspection (app) |
| 2 | Hazard communication (general industry) | 1910.1200 | Chemical inventory and SDS register; Hazard Communication Program Audit (app) |
| 3 | Control of hazardous energy, lockout/tagout (general industry) | 1910.147 | Lockout/tagout procedure template; Lockout/Tagout Audit and Periodic Lockout Review Audit (app) |
| 4 | Scaffolding (construction) | 1926.451 | Scaffold Inspection (app) |
| 5 | Ladders (construction) | 1926.1053 | Ladder Weekly Inspection and Working at Height and Ladder Inspection (app) |
| 6 | Respiratory protection (general industry) | 1910.134 | Respiratory Protection Program Audit and Respirator Inspection (app) |
| 7 | Powered industrial trucks (general industry) | 1910.178 | Forklift inspection checklist and forklift operator evaluation record; Powered Industrial Truck Operator Audit (app) |
| 8 | Fall protection, training requirements (construction) | 1926.503 | Training matrix; Fall Protection Program Audit (app) |
| 9 | Eye and face protection (construction) | 1926.102 | Eye and Face Protection Audit and PPE Compliance Audit (app) |
| 10 | Machine guarding (general industry) | 1910.212 | Machine guarding inspection sheet; Machine Guarding Inspection (app) |
Source: OSHA, Top 10 Most Frequently Cited Standards (osha.gov/top10citedstandards), FY2026 preliminary list, read on 21 November 2026. Templates marked (app) are in the LeanSuite Template Marketplace; find them by name in the inspection and audit template library. The rest are free printable templates.
The in-app templates are listed in the inspection and audit template library. In LeanSuite you open the Template Marketplace inside Lean Creator, find the template by its name and clone it into your plant, then change any question. For the method behind the top items, see the guides to lockout/tagout, PPE (eye, face and respiratory protection) and warehouse safety (forklifts), and the hierarchy of controls for choosing a fix that removes the hazard rather than guards against it.
What each audit checks and how often it runs
The LeanSuite templates for the top 10 come with a suggested frequency. Use it as a starting point and tighten it where the hazard or your own findings call for it.
| Template | Covers | Suggested frequency | Questions |
|---|---|---|---|
| Fall Protection Program Audit | The fall protection program | Monthly | 6 |
| Fall Arrest Equipment Inspection | Harnesses, lanyards and anchor equipment | Monthly | 10 |
| Hazard Communication Program Audit | The hazard communication program (1910.1200) | Monthly | 6 |
| Lockout/Tagout Audit | A lockout watched in progress, each step checked against the written procedure, per machine or crew (1910.147) | Monthly | 19 |
| Periodic Lockout Review Audit | Periodic review of lockout procedures (1910.147) | Monthly | 5 |
| Scaffold Inspection | Scaffolding (1926.451) | Weekly | 7 |
| Ladder Weekly Inspection | Portable ladders (1926.1053) | Weekly | 7 |
| Working at Height and Ladder Inspection | Ladders, platforms and fall protection before use or on a schedule | Monthly | 14 |
| Respiratory Protection Program Audit | The respiratory protection program (1910.134) | Monthly | 6 |
| Respirator Inspection | Reusable respirators and their parts (1910.134) | Monthly | 9 |
| Powered Industrial Truck Operator Audit | Truck operator behaviour and records (1910.178) | Monthly | 7 |
| Eye and Face Protection Audit | Availability, condition and use of eye and face protection (1926.102) | Monthly | 7 |
| PPE Compliance Audit | An area walk: the right protective equipment worn, in good condition and available | Weekly | 15 |
| Machine Guarding Inspection | Guards, interlocks and emergency stops, per machine (1910.212) | Monthly | 21 |
Frequencies and question counts are those of the LeanSuite templates, not OSHA requirements. Check the standard itself for any inspection interval it sets.
How to stay off the list: turn each standard into a recurring audit
- 1
Pick the standards that apply to your site
Half the list is construction and half is general industry. A plant usually starts with hazard communication, lockout/tagout, respiratory protection, powered industrial trucks and machine guarding, and adds ladders, scaffolds and fall protection wherever people work at height.
- 2
Clone a template for each one
Open the Template Marketplace inside Lean Creator and clone the template named in the table, or upload your own checklist as a PDF and Lean AI builds a digital version. Change any question to match your written programs.
- 3
Make the evidence required
Make a question required, flag an answer, ask a follow-up or require a photo. Every question is answered Yes, No or N/A, and a No is flagged and asks for a photo and a comment.
- 4
Schedule it to a person, a role or a machine
Schedule each audit in Daily Standard Work with a repeat rule. A machine guarding inspection or a lockout audit can be assigned to the asset, so its history stays with the machine. Assignees get an email reminder before it is due, and missed audits show in red.
- 5
Tie each audit to the standard it covers
Each scheduled audit can be tied to the requirement it fulfils, so today's audit shows which requirement it covers and you can show an auditor how each one is met.
- 6
Turn every No into a tracked action
A not met finding raises a tag, an idea or a Kaizen with an owner and a due date. Every audit, finding and corrective action is time-stamped and logged, and reports list every flagged answer across all audits, so you can see which standard keeps failing.
Two hazards on the list have their own modules. For lockout/tagout, LeanSuite runs each procedure as photo-verified isolation steps, the form will not open unless the user holds a valid Authorized Employee certification for that machine, and procedures get an owner and a yearly review date. See lockout/tagout software. Between audits, operators scan a QR code and log a hazard with a photo, with no app download and no login, and each corrective action is tracked until it is closed. See near miss reporting.
Sources
- Penalty amounts, minimums, the failure to abate limit, the repeated other-than-serious amounts and the reason for no 2026 increase: OSHA, Directorate of Enforcement Programs, memo of 21 May 2026, 2026 OSHA Civil Penalties Update: No Inflation Adjustment and Updated Minimum Penalties, Table 1 and footnotes 1 to 3 (osha.gov/memos/2026-05-21/2026-annual-adjustments-osha-civil-penalties).
- Maximum penalties and state plans: OSHA, OSHA Penalties (osha.gov/penalties), which links the Department of Labor's Federal Register notice of 27 May 2026, Annual Adjustments for 2026.
- The regulation: 29 CFR 1903.15(d), Adjusted civil monetary penalties, for penalties proposed after 15 January 2025 (osha.gov/laws-regs/regulations/standardnumber/1903/1903.15).
- Top 10 list: OSHA, Top 10 Most Frequently Cited Standards (osha.gov/top10citedstandards), preliminary list for fiscal year 2026, 1 October 2025 to 31 August 2026, page updated 5 October 2026. OSHA labels the list preliminary, so the final FY2026 list may differ.
- All pages read on 21 November 2026. Amounts are federal OSHA's and change with OSHA's annual adjustments; check osha.gov before relying on them. Not legal advice.
Audit Management
Audit the most cited OSHA standards in LeanSuite
Audit management in LeanSuite lets you build, schedule and run any shop floor audit or inspection, from layered process audits to gemba walks, and turn every finding into a tracked action.
Go deeper
This page is the short version. These guides cover each part in full.
- OSHA Audit Preparation: Reducing 40 Hours to 4 HoursHow keeping safety records current all year cuts the scramble before an OSHA inspection.
- Top Five Common Manufacturing HazardsElectrical, chemical, slip and fall, machine guarding and ergonomic hazards on the shop floor.
- Near Miss Reporting Prevents Future IncidentsHow reports of close calls find the hazard between audits, before anyone is hurt.
- Five Ways to Improve Safety on the Shop FloorHabits that keep the shop floor safe between inspections.
All our articles on this subject are in the safety management topic.
Free templates and tools
- Lockout/tagout (LOTO) procedure templateA machine-specific LOTO procedure: energy sources and isolation points, the steps from shutdown to restart, and the annual review.
- Machine guarding inspection sheetA machine register with due dates and a status per machine, 21 checks tied to OSHA 1910.212, .219 and .147, a guard opening check against Table O-10, and an action log.
- Forklift inspection checklist23 pre-shift checks for a week on one page, a do-not-operate rule, and a defect and repair log.
- Chemical inventory and SDS register templateA register of every chemical on site with its hazard class, safety data sheet and label, and a check that incompatible products are kept apart.
- Safety audit checklistThirty-four plant-wide safety checks answered Yes, No or N/A, scored by area, with a risk rating and an action for every No.
- OSHA compliance calendar (general industry)37 recurring federal OSHA duties with the paragraph, interval, owner, next due date and an overdue flag, plus a 12-month view and counts by owner.
- TRIR and DART rate calculatorOSHA recordable and DART incident rates from your 300A case counts and hours, and what one more case does to them.
Doing this in LeanSuite
Audit Management
Build, schedule and run any shop floor audit or inspection, and turn every finding into a tracked action with an owner.
See Audit ManagementLockout/Tagout
Guides authorized staff through each isolation step with photos and keeps a time-stamped audit trail, in place of paper LOTO binders.
See Lockout/TagoutNear Miss Reporting
Anyone logs a near miss, unsafe act or unsafe condition on their phone in seconds, and each corrective action is tracked until it is closed.
See Near Miss Reporting
See it on your own lines
Bring the problem you are working on to a 45-minute demo. Or look around with sample data first, or pilot LeanSuite on your own lines for 90 days, with the setup done by our team.
FAQ
Questions about oSHA penalties and the top 10 cited standards
$165,514 per violation for a willful or repeated violation, and $16,550 per violation for a serious, other-than-serious or posting violation. Failure to abate can cost up to $16,550 for each day past the abatement date, generally limited to 30 days. Source: OSHA memo of 21 May 2026 and osha.gov/penalties.
No. OSHA's memo of 21 May 2026 says there are no inflation-based increases for 2026 and the 2025 amounts remain in effect, because the Bureau of Labor Statistics could not produce the October 2025 consumer price data during the government shutdown.
In OSHA's preliminary list for fiscal year 2026: fall protection general requirements (1926.501), hazard communication (1910.1200), lockout/tagout (1910.147), scaffolding (1926.451), ladders (1926.1053), respiratory protection (1910.134), powered industrial trucks (1910.178), fall protection training (1926.503), eye and face protection (1926.102) and machine guarding (1910.212).
Fall protection, general requirements, in construction (29 CFR 1926.501) is first in OSHA's preliminary fiscal year 2026 list. The most cited general industry standard on that list is hazard communication (29 CFR 1910.1200), in second place.
$1,085 per violation in 2026, according to OSHA's 21 May 2026 memo. That minimum comes from OSHA's penalty policy, at the lowest gravity level with the largest reductions allowed. The minimum for a willful violation, $11,823, is set by statute.
Check each cited standard that applies to your site on a schedule, before an inspector does: a recurring audit per standard, assigned to a person, role or machine, with photos as evidence and every failed item turned into an action with an owner and a due date.
Related guides and tools
More method guides
- The 6 Ms of production
- Poka-yoke
- Model area 90-day plans
- Moving from Excel to one system
- Reducing machine downtime: a worked month
- Andon
- Cycle time vs lead time, worked through
- Root cause analysis
- How many operators a line needs
- Reducing scrap and rework: a worked month
- Unsafe acts and unsafe conditions
- Just culture
- Stop-work authority
- Material review board (MRB)
- Nonconformance and NCRs
- Problem solving methods
- Quad chart
- OEE calculation
- Quality assurance vs quality control
- SOP meaning and format
- Job hazard analysis
- Near miss reporting
- Fishbone diagram
- Pareto chart
- Histogram
- Control chart
- What is a gemba walk
- What is lead time
- What is operational excellence
- How to improve product quality
- Preventive vs predictive maintenance
- Kanban
- FMEA
- PDSA cycle
- Safety moments
- Just-in-time manufacturing
- Kaizen
- 5S
- Total quality management (TQM)
- CAPA (corrective and preventive action)
- Layered process audit (LPA)
- Lean tools
- Lockout tagout (LOTO)
- A3 problem solving
- Preventive maintenance
- APQP
- High reliability organization (HRO)
- Manufacturing KPIs
- Quality metrics
- Practical problem solving
- CMMS
- Risk assessment
- Production efficiency
- Total productive maintenance (TPM)
- Reliability-centered maintenance (RCM)
- Hierarchy of controls
- Personal protective equipment (PPE)
- Emergency action plan
- Safety signs
- Warehouse safety
- ISO 9001
- SIPOC diagram
- Rolling action item list (RAIL)
- Pugh matrix
- Flowchart
- Project charter
- ISO 9001:2026
- Fleet maintenance
- IATF 16949
- AS9100
- ISO 14001
- ISO 45001
- One point lesson
- Standard work
- Meeting cadence
- Lean manufacturing principles
- Toyota Production System
- 5W1H
- 5 Whys
- Continuous improvement
- Takt time
- DMAIC
- PDCA
- 8D problem solving
- Prioritization matrix
- Gemba walk questions
- 5W1H questions
- Layered process audit questions
- 5S audit questions
Or browse the topics, the full library and the lean glossary.
Rather see it on your own problem?
Bring the problem you are stuck on, and we will show you on a call how LeanSuite handles it.

